DX Hydro / DX Sound Co.
3807 Lanewood Dr.
Des Moines, IA 50311

info@dxhydro.com
415-800-DXCO or 515-897-1801
Skype: dxsoundco.com

website security

 

 

 

QUICK LINKS, ETC

  Do I need a lighting controller?
  Parts, Kits, DIY

  240V Wiring Info
  120/240V System Explained
  Why do I need Four Prongs/Wires?
  Wire Ampicity/NEC Table 310.16
 

Index: 

Standard Lighting Controllers

Upgrades & Options

Build Time & Shipping Info

Service & Warranty Support


Kind Design
10-12 Lights with High Temp Cut-Off, Hot Start Delay, 8 continuous 120v outlets & optional power meter
 

With twelve timed and eight continuous outlets, high-temperature cutoff and hot start delay, this controller is perfect for a medium size one or two room setup.
With the standard configuration it's set up to run ten 240v HID lights & two fans to keep the lights cool on the on the timer cycle, along with four smaller 120v lights on a 24 hour cycle.
Another four outlets for fans, irrigation, pumps, etc.  make this a perfect controller to run your entire setup using one 40-80* amp feeder from your main panel.
*feeder requirement depends on you load & lamp size

Click HERE for Product Page

only $520
Add $69 for digital power meter @ $589

 

Most custom configurations are free of charge unless they require additional materials or excessive labor.
If you need NEMA 5-15 receptacles installed for your 240v lights -No Problem & No Charge!

Digital Temp Controller can be used to control HVAC rather than High-Temp Cutoff.
    *****Have it your way!*****

Options
Timed receptacle configuration
Special Requests:
 

 

BUY AMERICAN
All DX Hydro Controllers & Panels are Built to American Standards, by Americans, in America!

Flippers and Flip Boxes are not created equal
Check out this article about our
Smart Flipper™

The Dumb Flip Box VS. the Smart Flipper

 


NEED PARTS or KITS?

Click HERE
Page is under construction (Not much to look at!)
RELAYS/DELAYS/TIMERS/CORDS & CABLE/BALLASTS/KITS/TESTERS & TOOLS
Not everything is listed yet, email if you need something


 


 

 

 

 

 

 

 

 


 

Lighting Controllers
 

Incredible LOW introductory Price
 
$244.20

               
Check out the new DX16 Lighting Controller
With OPTIONAL Z-Wave Remote Control
Options
Outlet Configuration
Other option avail / will call

 


The POWER THIEF

Confuguration

NEMA Cord Selector


 

Many people use their dryer outlet for grow lights. Some go as far as to build adapters or even disconnect the lights and plug their dryer in every time they need to do laundry! Here's an easy solution:
Use your existing dryer outlet for your dryer AND up to 6Kw of Grow Lights
Simply plug into your dryer outlet, plug your dryer & lights into POWER THIEF, set the timer and, that's it!
Dryer will be available only when lights are off -will never overload circuit.
NO WIRING NEEDED * PLUG-N-PLAY
Great for Rental Properties -Just unplug the unit & take it with you!


 

Custom Orders Are Our Specialty

If there is any option on any controller you would like but it's not listed, No Problem!
Just send an email & we'll customize a controller for you.
 


 

Only
$244.20
(plus s/h)

 

12Kw Controller
Twelve timed 240V outlets Plus two convenience outlets
50-AMP Plug & Go Control


Shown with dual timers - select single/dual timer from drop-down menu

Single/Dual Timers
Outlet Configuration (timed outlets)
Plug-In or Direct Hookup

 

All controllers with 240v outlets come equipped with NEMA 6-15R receptacles.
If you want to use your standard 120v power cords we can substitute NEMA 5-15R receptacles so you can use your original 120v power cords for 240 volt operation.
PLEASE NOTE
Extreme care must be taken to prevent connecting a 120 volt device to a 240v outlet.
We recommend the use of child-proof protectors to cover any unused outlets*.


Additional Options Below
(Delays, Power Meters, Etc.)
If you need Additional Custom Features Please email.

Back to Top

12Kw Controller Features
 

  • Plugs into 50 amp, four-prong range outlet (Nema 14-50R)

  • 12,000 watts of power!

  • 12 Timed outlets 240V standard*
    Optional 120-volt type plugs so you don't need to change cords for 240-volt operation.

  • On-Board digital timer

  • All heavy duty steel construction     -uses Square-D 100A breaker panel with two internal high-power relays controlled by timer.

  • Two 120V convenience outlets -Always on.

  • 50A Hard-Wire Option comes with 3' liquid-tight power whip instead of power cord.

  • 60 Amp version requires your wiring from main panel to the controller/No cord or whip is included (send me a note indicating 60A +) Panel is rated for up to 100A feeder.
     

 

Dual Timer 12Kw Controller
Same as above but with two timers.
and each bank of 6 outlets is controlled by it's own timer, relay and breaker.
No convenience outlets.
$294.20 (plus s/h)


Questions?



Only

$224.20
(plus s/h)

Deluxe 7200W controller
Eight timed 120 or 240V outlets Plus four always-on 120v outlets
30-AMP Plug & Go Control


 

Single/Dual Timers
Outlet Configuration (timed outlets)
Plug-In or Direct Hookup



All controllers with 240v outlets come equipped with NEMA 6-15R receptacles.
If you want to use your standard 120v power cords we can substitute NEMA 5-15R receptacles so you can use your original 120v power cords for 240 volt operation.
PLEASE NOTE
Extreme care must be taken to prevent connecting a 120 volt device to a 240v outlet.
We recommend the use of child-proof protectors to cover any unused outlets*.

NO CHARGE!
JUST NOTE OUTLET PREFERENCE IN MESSAGE WITH YOUR PAYMENT

Additional Options Below
(Delays, Power Meters, Etc.)
If you need Additional Custom Features Please email.



Deluxe 7200W Controller Features
 

  • Plugs into 30 amp, four-prong dryer outlet (Nema 14-30R)

  • 7200 watts of power!

  • 8 Timed outlets 4x120 & 4x240 volt standard*
    (can be wired for 120 or 240 volt operation)

  • On-Board digital timer

  • All heavy duty steel construction     -uses Square-D 100A breaker panel with internal high-power relay controlled by timer.

  • Four 120V convenience outlets -Always on.

  • Hard-Wire Option comes with 3' liquid-tight power whip instead of power cord.

Upgrade to dual timers for $70.
Two controllers in one box!

Questions?


Only
$144.20
(plus s/h)

BASIC CONTROLLER
WITH TIMER & TRIGGER CABLE

30-AMP Plug & Go Control

 


NOTE that the Basic Controller standard configuration, like most 30 amp lighting controllers on the market, the outlets are connected directly to a 30A circuit. The difference is that the DX Hydro Basic Controller has an onboard circuit breaker & the others relay on the 30 amp breaker in your main panel. We think this provides better protection in the case of a short circuit or other fault.
The Basic Controller can be set up with an be set up with additional circuits at  the cost of materials. 

Single/Dual Trigger
Outlet Configuration

All controllers with 240v outlets come equipped with NEMA 6-15R receptacles.
If you want to use your standard 120v power cords we can substitute NEMA 5-15R receptacles so you can use your original 120v power cords for 240 volt operation.
PLEASE NOTE
Extreme care must be taken to prevent connecting a 120 volt device to a 240v outlet.
We recommend the use of child-proof protectors to cover any unused outlets*.

NO CHARGE!
JUST NOTE OUTLET PREFERENCE IN MESSAGE WITH YOUR PAYMENT


Additional Options Below
(Delays, Power Meters, Etc.)
If you need Additional Custom Features Please email.

Basic Controller Features
 

 
  • Plugs into 30 amp, four-prong dryer outlet (Nema 14-30R)

  • 7200 watts of power!

  • Four each 120 & 240v outlets standard. Order with any combination of 120 or 240v outlets, timed or continuous, NEMA 5-15 or 6-15R receptacles.
    (Have it your way!)

  • Comes with digital timer and has a six-foot trigger cord for control of all eight outlets.

  • All heavy duty steel construction     -uses Siemens 125A breaker panel with internal high-power relay controlled by trigger cable.

  • This is our most economical panel-based controller but don't let the low price fool you. It is the same high quality construction as all of our controllers.

  • Hard-Wire Option comes with 3' liquid-tight power whip instead of power cord.
    SOOW cable available too.

Dual Trigger Basic Controller
Same as above but with more power
and each bank of outlets is controlled by it's own timer, relay and breaker.
40-amp supply cord (requires Nema 14-50R receptacle running on 40A main). Two digital timers included.
9600 Watts!

$194.20 (plus s/h)
 


 

 
 

   


Only

$194.20
(plus s/h)

BASIC PLUS CONTROLLER 
WITH ONBOARD DIGITAL TIMER

30-AMP Plug & Go Control


Please note that the red outlet cover isn't standard and this customer chose to have NEMA 5-15R receptacles installed in place of the NEMA 6-15R for the 240v outlets (see notes below).
Also shown with optional whip connection

Outlet Configuration
Plug or Direct Wire

 

All controllers with 240v outlets come equipped with NEMA 6-15R receptacles.
If you want to use your standard 120v power cords we can substitute NEMA 5-15R receptacles so you can use your original 120v power cords for 240 volt operation.
PLEASE NOTE
Extreme care must be taken to prevent connecting a 120 volt device to a 240v outlet.
We recommend the use of child-proof protectors to cover any unused outlets*.

NO CHARGE!
JUST NOTE OUTLET PREFERENCE IN MESSAGE WITH YOUR PAYMENT



Basic Controller Plus Features
Same as Basic Controller with onboard timer


 

  • Plugs into 30 amp, four-prong dryer outlet (Nema 14-30R)

  • 7200 watts of power!

  • All outlets 240 Volt standard*
    Optional 120-volt type plugs so you don't need to change cords for 240-volt operation.

  • Onboard digital timer.

  • All heavy duty steel construction     -uses Siemens 70A breaker panel with internal high-power relay controlled by trigger cable.

  • This is our most economical controller but don't let the low price fool you. It is the same high quality construction as all of our controllers.

  • Hard-Wire Option comes with 3' liquid-tight power whip instead of power cord.

 

 

Additional Options Below
(Delays, Power Meters, Etc.)
If you need Additional Custom Features Please email.

 

 

Starting at Only
$99.00
(plus s/h)

30 Amp Light Controller
Four timed 240V outlets
30-AMP Plug & Go Control
DX-4T shown
DX-4 & DX-6
Series
Lighting Controllers
 

DX-4T with onboard timer shown.
DX-4 has trigger cable for external timer/controller

Select Configuration
Select Power Cord/Plug


All controllers with 240v outlets come equipped with NEMA 6-15R receptacles.
If you want to use your standard 120v power cords we can substitute NEMA 5-15R receptacles so you can use your original 120v power cords for 240 volt operation.
PLEASE NOTE
Extreme care must be taken to prevent connecting a 120 volt device to a 240v outlet.
We recommend the use of child-proof protectors to cover any unused outlets*.

NO CHARGE!
JUST NOTE OUTLET PREFERENCE IN MESSAGE WITH YOUR PAYMENT

  • Plugs into 30 amp dryer outlet or HardWire

  • 7200 watts of power!
    (6Kw available)

  • 4-6 Timed outlets 240V standard*

  • Optional 120-volt type plugs so you don't need to change cords for 240-volt operation*

  • NEMA 6-15 240v outlets available for $2 each

  • DX-4 has trigger cable -uses your external timer or controller

  • DX-4T (shown in pic) has onboard digital timer

NOTE:
Please let me know which power cord you need -Three or Four Prong
(NEMA 10-30 or 14-30)
Can also  be ordered with 20 amp (NEMA 6-20 plug) cord -good for four lights @ 240v.

 

If you need Additional Custom Features Please email.


Questions?

   

*Do not plug in ANY 120 volt devices into the sockets on
the controller configured for 240 volt operation.
You will instantly destroy any 120 volt device that is plugged in!

SMOKE ALARMS AND FIRE EXTINGUISHERS SAVE LIVES!

 

Back to Top


Misc. Upgrades & Options:

  Two-minute sequential delay
for larger, multi-relay controllers only (reduce start-up load): $24.00



  Adjustable Hot-Start Delay
Uses industrial delay for dependability and accuracy: $55.00
User adjustable from milliseconds to hours -Comes setup for 15-minutes


 


Add a Digital Power Meter to your Controller
$80
(100 amp capacity -Higher capacity models slightly higher)

 

Other options include:
High Temp Cutoff,
Wireless control via Z-wave,
Remote Kill Switch,
Fire/Heat Detector* to kill power in the event of a fire
*NOT A LIFE-SAFETY DEVICE & NOT A REPLACEMENT FOR FIRE & SMOKE DETECTORS!

Anything else you can think of to make your controller more useful?
 


standard 120v outlet

240v outlet



Current Standard outlets for Dryers & Ranges
Four-Wire circuit required WHY?
Click HERE for 240v wiring info
 

 

Back to Top


Build Time & Shipping


All of our controllers are Custom Built for our customers - Please allow about 5 business days build time in addition to shipping time.
Please note that Shipping charges listed in the PayPal shopping cart are Cont. US only. Canada, & other destinations will be charged actual shipping cost.
You will receive a notification when your shipping label is printed -
Your package might not actually leave here until the next pickup time so the tracking information may not be immediately updated.
If you need expedited service let me know and we'll try to accommodate you & put in some extra time to get your order completed.
I will not, under any circumstances, move your order ahead of other customers but, will instead work beyond my normal schedule to get it done.
Please don't abuse this option: use it only if you really need it -like if there is a potential safety concern & you're blowing breakers, etc.
Overtime labor rate will apply.


We will be adding more options to our site soon. If you don't see something that will work for you PLEASE, send an email-
WE CAN BUILD IT.
That's our specialty, building custom controllers for growers like you!
The lighting controller is the most abused piece of equipment in the grow room or greenhouse but is often something overlooked. Instead of investing in a good lighting controller, too many people opt out, instead using cheap timers that were made to control a table lamp to control their grow lights. In one test garden we used a high quality plug in timer rated for 15 amps on a 1000W HID -That's about a 9.5 amp load but the timer ran hot all the time (a sign of a voltage drop due to excessive resistance) and failed after six weeks.
Power strips and cheap timers are the largest cause of grow room fires, causing hundreds every year!
We build our controllers with only the highest quality, UL listed materials. We don't have a fancy box or a million-dollar ad campaign so you don't pay for it.
The workmanship and materials on the inside are what matters -the rest is for appearance, means absolutely nothing but costs you money.
All of the work is done in our shop here in Des Moines, Iowa -Nothing is farmed out & every unit is inspected & load-tested before it ships.
We don't use cheap, inferior-quality outlets that say "made in Taiwan" on them to save a buck (I won't name names
If you need to replace a breaker some day, you can go to Home Depot & buy one.
If you buy one of our controllers, you will be making an investment in a product that will last a lifetime with proper care & minimal maintenance.
 

Back to Top


Any questions about any items here or on eBay -Please email!
dweddle@dxsoundco.com

Do it right the first time

 

 

copyright 2010/2011 DX Sound Co. - Problems with page contact web@dxsoundco.com